| Under Setup you can configure the installation settings, perform a Freesat Tune, Manual Tune, update software and restore the receiver to its Factory settings. |
| Freesat Tune |
| A Freesat Tune will only list TV and radio channels currently listed on the Freesat EPG (Electronic Programme Guide). For all other Free-To-Air (FTA) channels, a Manual Tune is required. |
1. Press the MENU button.
2. Select Setup using the arrow keys and press the OK button.
3. Select Freesat Tune using the S/T button and press the OK button.
4. Enter your region code (This is your full Postcode with a space in between).
5. Please note that once you perform Freesat Tune, all Freesat channels will be deleted. Select Yes and press the OK button to delete all freesat channels.
6. Select Search and press the OK button to search channels.
7. The channel search will start.
8. To stop the search, press the OK button during channel search.
9. The results will appear. Select Save and press the OK button. |
|
| Manual Tune |
1. Press the MENU button.
2. Select Setup using the arrow keys and press the OK button.
3. Select Manual Tune using the arrow keys and press the OK button.
4. Select Search and press the OK button. The channel search will start.
5. To stop the search, press the OK button during channel search.
6. The results will appear. Select Save and press the OK button. |
| Transponder |
| Select All or the value in the transponder list and press the OK button. If the required value is not available, select User Define and enter the transponder value directly. |
|
| Software Update |
Software Update allows you to update the system software to maintain proper performance of the receiver.
1. Press the MENU button.
2. Select Setup using the arrow keys and press the OK button.
3. Select Software Update using the arrow keys and press the OK button. |
| Automatic Update |
1. Select Automatic Update and press the OK button.
2. When new software is detected, you can choose to download the software immediately or save for later.
3. When there is no new software to update, a popup will appear. |
| Manual Update |
1. Select Manual Update and press the OK button.
2. Enter the values for Satellite, Frequency, Polarization, Symbol Rate and FEC.
3. Select Search and press the OK button.
4. When new software is detected, you can choose to download the software immediately or save for later.
5. When there is no new software to update, a popup will appear. |
| Over The Air Download |
OTA, an abbreviation of Over–the-Air, is a standard for the transmission of software through a broadcast system. OTA is an alternative method for downloading software versions. However, the manufacturers reserve the
right for deciding the release of the software for their products by transmitting the latest software versions over the air via satellite.
The following factors must be in place for the software update via satellite to occur:
|
1. The equipment has the appropriate loader software.
2. The manufacturer decides to release the software via a designated satellite.
3. The equipment is tuned properly to the same antenna equivalent to that of Freesat (28.2° east).
4. The signal strength and quality is high. If severe weather conditions or your location are affecting reception, for example, the software update should be postponed until signal strength and quality are favourable again.
|
CAUTION:
Please note that if the normal loader software is not equipped, the product may not be updated or operate properly after software update.
Keep the power on and the power cord plugged in during software update. If the power is off during software update, fatal damage may be caused to the receiver.
Do not remove the antenna (LNB cable) during software update. |
NOTE:
It may take 5~10 minutes to update software.
Other functions will not activate while software update takes place.
You cannot schedule programmes during software update. |
| Software update while watching a programme |
When new software is detected, you can choose to download the software
immediately or save for later. In case there is no software currently
available, select Next and press the OK button to proceed to the next
step. |
| Software update via USB |
Copy the software to the USB memory stick and connect the USB to the
receiver. Press the STANDBY
button and turn off the power. To power on, press the STANDBY button while
switching on the receiver
to start software update. |
|
| Factory Reset |
Factory Reset enables you to restore the product to the factory default.
WARNING: Please note that once you perform Factory Reset, all data such as the antenna setting information, channel list and all user configured data will be deleted.
NOTE: The default password is 0000. |
1. Press the MENU button.
2. Select Setup using the S/T button and press the OK button.
3. Select Factory Reset using the S/Tbutton and press the OK button.
4. Select Yes and press the OK button to restore all setting to factory default. To return to the previous menu, select No and press the OK.
5. You will be prompted to enter your password again before starting to load factory reset. Enter the password to proceed.
6. When factory reset is completed, the first installation appears automatically and assists channel search. |