| First Installation/Freesat Tune |
| This guide is based on the Humax FOXSAT-HD Freesat receiver, the installation procedure may vary depending on the model and manufacturer of your receiver. |
| NOTE: The default password is 0000. |
| Make sure the satellite receiver is connected to the satellite dish, then turn on the device. The first installation will operate automatically. |
| User Settings |
|
| User Settings allows you to set the language, screen ratio, display format and resolution. |
| Select a language option from Preferred Language (English Gaelic or Welsh), Picture Format and Resolution. |
| Select Next and press the OK button. |
| NOTE: |
| If the product is connected to the TV using an HDMI cable, Original will not be displayed. |
| |
| |
| |
|
|
|
| Freesat Detection |
|
| 1.Confirm the antenna cable is connected and press the OK button to find Freesat. |
| 2. Wait until Freesat detection is complete. |
| 3. When Freesat is detected, press the OK button to go to the next step. |
| If Freesat is not detected, check your satellite antenna cable connection and that your satellite dish is aligned to the Astra 2 group of satellites copositioned at 28.2° east. |
| NOTE: |
| Always turn the receiver off at the mains before checking the antenna cable and connection, failure to do so could result in permenent damage to your receiver and Electric Shock. |
| |
| |
|
|
|
|
The receiver is now searching for Freesat. This should take no more than two minutes. If no signal is detected, check your dish and cables. |
A Direct Cable connection has been detected. This is a single dish installation, not a DiSEqc multi satellite setup.
|
|
|
| Postcode |
Enter your full postcode (including a space) using the NUMERIC(0-9) button on the remote control.
To use on-screen keyboard, press the OPT+ button. Press the 1 button to enter a space.
NOTE: You must enter your entire postcode including the space. |
You can always change the desired postcode in the Freesat intallation menu by changing the post code. You must rescan in Freesat mode and then save for the changes to take affect.
There are hundreds of postcodes in the UK, to change region type in one of the following: |
|
| Region |
Postcode |
Anglia |
NR1 3JG |
Border |
CA1 3NT |
Central |
B1 2JT |
Channel |
JE1 3ZD |
Granada |
M60 9EA |
HTV Wales |
CF5 6XJ |
London |
WC1X 8XZ |
Meridian |
ME14 5NZ |
HTV West |
BS4 3HG |
Westcountry |
PL7 5BQ |
Tyne Tees |
NE11 9SZ |
|
|
| Overseas Reception & Regional Settings |
Outside the official Astra 2D footprint, reception of your default region may be difficult. Apart from some local variations, the BBC's and ITV1's programming is more or less identical.
All BBC and ITV regions are available on satellite, though quite a few are still missing at present from Freesat's EPG.
Some regions use horizontal and some vertical transponders. Signal strength from horizontal and vertical transponders varies considerably from country to country, so your default region may not give the best reception in your area.
Try one of the following combinations: |
| Region |
Postcode |
Area |
Polarization |
| BBC One SE & ITV1 London |
TN13 1AA |
Seven Oaks, Kent |
Vertical |
BBC One Scotland and ITV Border North |
TD7 5EA |
Selkirk |
Horizontal |
|
|
| Search Channels |
| Search Channels will activate and the results will appear. To stop the channel search, select Stop and press the OK button. Select Save and press the OK button to go to the next step. |
|
|
|
This search only saves channels currently available through the Freesat Electronic Programme Guide (EPG).
To add other channels, you must do a Manual Tune. |
Save the results, this will be complete when the blue saving bar reaches 100%.
The installation will then continue to the final completion page.
|
Listed on the Result page are your prefered language, Picture Format, Postcose & channels found. Press Finish to complete the Freesat Installation. |
|
|
| Manual Tune |
|
| 1. Press the MENU button. |
| 2. Select Setup using the arrow keys and press the OK button. |
| 3. Select Manual Tune using the arrow keys andthen press the OK button. |
| 4. Select Search and press the OK button. The channel search will start. |
| 5. To stop the search, press the OK button during channel search. |
| 6. The results will appear. Select Save and press the OK button. |
| |
| |
|
|
|
| Multi Satellite Setup - DiSEqC (Humax Only) |
|
| The Humax FOXSAT-HD receiver performs just like a fta receiver, you can select the satellites,select the port(s) for the satellite(s),and scan. |
| Accessing the DiSEqc/motorised menus, is via a secret menu, by pressing the colour buttons in the following sequence: |
| RED, GREEN, YELLOW, BLUE, GREEN, YELLOW, BLUE |
| For a full DiSEqC setup Guide, click HERE. |
| |
| |
| |
|
|
